R-Tune Modified Rotor 5 - 12.5 SM

Dash 540 Motor Screw Allen Countersunk M2.5x7mm Golden Alu 7075 (3 pieces)

Dash 540 Motor Screw Allen Cilinder M2.5x45mm Golden Alu 7075 (3 pieces)

The Tunalyzer is the latest tool that Hobbywing recommends to any RC hobbyist who wants to achieve optimal results when selecting and maintaining motors. Achieve meaningful and accurate results with 12 preset test parameters. The measurement is supported, among other things, by the built-in voltage regulator, which ensures that comparable results are always obtained under...

Fits HobbyWing 4268 G2 / G3 Brushless motor for 1/8. Contains one each: 5x16x5mm 5x11x5mm Genuine HobbyWing bearings - directly from their service department, without a box.

Nice tool whichs helps to replace a rotor within a few moments. Will fit to 1/10 motors, type 540. Maximum rotor diameter is 13.0mm. Not only for HobbyWing motors!

XERUN V10 G3 - Rotor 12.1mm - D5 - 24.1mm length

XERUN V10 G3 - Rotor 12.5mm - D5 - 24.1mm length

XERUN V10 G3 - Endbell Set - On-Road Stock - incl. Sensor Unit Fits motors 10.5-25.5T (Hole B). Weight: 24,3g

XERUN V10 G3 - Endbell Set - On-Road Modified - incl. Sensor Unit Fits motors 5.5-8.5T (Hole S). Weight: 25g

XERUN V10 G4 - Rotor 12.5mm - F7 - 25.2mm length

XERUN V10 G4 - Rotor 12.5mm - F7 - 24.1mm length

Includes front and rear endbell, bearings, sensor unit and screws.

XERUN Bandit G4 - Rotor 13.9mm - D5 - 24.1mm length

XERUN Bandit G4 - Rotor 13.3mm - D5 - 24.1mm length

Fits most 540 1/10 brushless motors

Increases the motor shaft diameter from 3.17mm to 5mm for bigger pinions.

Motor Ball Bearing 694ZZ, 4x11x4mm (2pcs) Standard replacements ball bearings, to be used to LRP X12 Stock Spec brushless motors.

X12 StockSpec Rotor - Standard Standard sintered spare rotors to the X12 Stock Spec brushless motors. Magnet material 12.45mm Sintered Rotor

X12 StockSpec Rotor - Standard Standard sintered spare rotors to the X12 Stock Spec brushless motors. Magnet material 12.45mm Sintered Rotor

X22 Aluminium Backplate - Black

X22 WorksTeam Modified Rotor - 12.5mm

X22 WorksTeam Modified Tuning Rotor - 12.1mm

X22 WorksTeam Modified Tuning Rotor - 12.3mm

X22 WorksTeam Modified Tuning Rotor - 12.7mm

X22 WorksTeam Modified Tuning Rotor - 13.0mm

X22 Small Parts Set

X22 Modified Housing - Front

X22 Motor Bearing 4x10x4mm - (2pcs)

LRP 520521 - X22 Rotor - 12.3mm Specially made for the 520305 X22 N.B. 6.5T motor.

X22 PreciSensor-Unit Will replace also the older unit 50623 when it should be sold out.

X22 Brass Endcover with cooling fins This new brass tuning part with cooling fins improves the heat dissipation significantly compared to the standard plastic endcover. Featured with laser engraved XTEC logo and A, B, C speedo cable connection, giving your motor a stylish look! Due to its special design the motor has better heat-dissipation and ventilation, resulting in a...

LRP 520521 - X22 Stock Spec Tuning Rotor - 12.3mm

X22 Stock Spec Rotor - 12.5mm

Suitable for X22 Stock Spec motors.

MuchMore CE-MPG - 3.5mm Motor Ceonnector Set - 3x Male + 3x Female

Aluminium Screw Set for Fleta ZX V2 Motors - Orange - (6pcs)

Aluminium Screw Set for Fleta ZX V2 Motors - RED - (6pcs)

Aluminium Screw Set for Fleta ZX V2 Motors - Silver - (6pcs)

Suitable for any FLETA ZX V2 motor. Please note: There is a letter printed on the sensor unit. This will be different from batch to batch. It's L which is shown in the picture - this may be different from what you'll receive.

N22 Brass Endcover with cooling fins This new brass tuning part with cooling fins improves the heat dissipation significantly compared to the standard plastic endcover. Featured with laser engraved XTEC logo and A, B, C speedo cable connection, giving your motor a stylish look! Due to its special design the motor has better heat-dissipation and ventilation, resulting in a...

Blitreme 2 / Modtreme Motor Sensor Unit

Fits for 13.5T and also 17.5T version of our motor!

Fits for 13.5T and also 17.5T version of our motor!

Fits for 13.5T and also 17.5T version of our motor!

Fits for 13.5T and also 17.5T version of our motor!

Fits for 13.5T and also 17.5T version of our motor!

Fits for any RUDDOG RP540 motor!

You are having trouble with mounting your brushless motor in the XRAY T4 2020? You don't want to cut your upper deck or the motor case? Just use these graphite spacers - combined with (non included) longer screws to get a working solution. This set will contain two spacers - one with 2.0mm and one with 3.0mm thickness.

EMPTY spare bottles for super glue. 10ml size. Set of five.

Fits for 13.5T and also 17.5T version of our motor!

Fits for 13.5T and also 17.5T version of our motor!

Fits for 13.5T and also 17.5T version of our motor!

Fits for 13.5T and also 17.5T version of our motor!

Replacement stack!

Sonic 540-SP5 Titanium Motor Screw Set 3x M2.5x6mm 3x M2x45mm

Sonic 540-SP5 Sensor Board

Sonic 540-SP5 Motor Screw Set

M3x7mm Titanium Brushless Motor Mount Screws (2 pieces)

Titanium Rear Wing Mount Screws (2 pieces)