Anti Roll Bar for Ball Bearings - Front 1.5mm

Anti Roll Bar for Ball Bearings - Front 1.6mm

LiPo CHASSIS GRAPHITE MOTOR GUARD

Genuine spare and option parts from XRAY!

SET OF ALU SHIM (0.5MM, 1.5MM, 2.5MM)

SET OF ALU SHIM (1.0MM, 2.0MM, 3.0MM)

T4 2014 - Alu Shims (3x6x0.5mm) - black

T4 2014 - Alu Shims (3x6x0.5mm) - orange

T4 2014 - Alu Shims (3x6x0.5mm) Will be delivered BULK.

ALU SHIM 3x6x1.0MM (10)

ALU SHIM 3x6x1.0MM - ORANGE (10)

XRAY T2 Alu Scheiben - 3x6x2.0mm (10 Stück)

ALU SHIM 3x6x2.0MM - ORANGE (10)

Alu Shim 3x5x1.0mm - ORANGE (10 pieces)

Alu Shim - 3x5x0.5mm - BLACK (10)

XRAY 303142-O - T4 Alu Shim - 3x5x0.5mm - Orange (10)

T4 Alu Shim 3x5x0.25mm (10)

XRAY 303142-O - T4 Alu Shim - 3x5x4mm (10)

XRAY 303142-O - T4 Alu Shim - 3x5x4mm - Orange (10)

T4 2014 Rear Suspension Arm - Graphite

ARS Active Rear Suspension Arm - Graphite - 1-Hole

The aluminum suspension arm is a direct replacement for the standard composite graphite arm. The aluminum arm works well on high traction or permanent carpet tracks as it makes the car easier to drive with less stopping and better cornering speed. The arms are available for front and rear and are available either individually or as a set. Features a single optimized shock...

T4 2014 Graphite Rear Arm Stiffener (2) Important note : The carbon plates are fastened with screws M2.5 with 1.5mm allen head. Therefore it is extremely important to use a hex screwdriver is in a state of 100 %. A hexagon with wear will destroy the screws . It is also necessary to go with caution to the screws . Not tighten too fast , do not fix sloping ! In order to be...

Graphite ARS Rear Lower Arm Plate 1.6mm (L+R)

REAR TURNBUCKLE L/R 26 MM - HUDY SPRING STEEL (2)

ALU ADJ. TURNBUCKLE L/R 26 MM - ORANGE - SWISS 7075 T6 (2 pieces)

COMPOSITE UPRIGHT 1° OUTBOARD TOE-IN - RIGHT - MEDIUM

COMPOSITE UPRIGHT 0° OUTBOARD TOE-IN - MEDIUM

COMPOSITE UPRIGHT 1° OUTBOARD TOE-IN - RIGHT - HARD

COMPOSITE UPRIGHT 1° OUTBOARD TOE-IN - LEFT - MEDIUM

COMPOSITE UPRIGHT 0° OUTBOARD TOE-IN - 1-HOLE - MEDIUM

COMPOSITE UPRIGHT 1° OUTBOARD TOE-IN - LEFT - HARD

COMPOSITE UPRIGHT 0° OUTBOARD TOE-IN - 1-HOLE - HARD

ALU LOWER 2-PIECE SUSPENSION HOLDER (1 Piece)

T4 2014 ALU REAR LOWER 1-PIECE SUSPENSION HOLDER - FRONT Does NOT fit into T4 2017.

• 3x heavier than alu holders • Eliminates need for additional chassis weights • Eliminates negative chassis flex • Equal weight addition left & right • Available for front or rear suspension Brass suspension holders were created to add additional weight to the car to attain the minimum weight limit, and to replace other chassis-mounted weights which negatively influence...

• 3x heavier than alu holders • Eliminates need for additional chassis weights • Eliminates negative chassis flex • Equal weight addition left & right • Available for front or rear suspension Brass suspension holders were created to add additional weight to the car to attain the minimum weight limit, and to replace other chassis-mounted weights which negatively influence...

Alu lower RIGHT suspension holder CNC-machined from premium Swiss 7075 T6 aluminum. Suitable for standard rear suspension, also suitable for ARS with extra roll center positions. The lower design of the suspension holders helps to generate more traction. Recommended for use on asphalt tracks with low-to-medium traction. Must be used with: left alu holder #303717-O and Rear –...

Alu lower LEFT suspension holder CNC-machined from premium Swiss 7075 T6 aluminum. Suitable for standard rear suspension, also suitable for ARS with extra roll center positions. The lower design of the suspension holders helps to generate more traction. Recommended for asphalt tracks with low-to-medium traction. Must be used with: right alu holder #303716-O and Rear – rear...

Authentic XRAY alu rear lower suspension holder for the REAR of the front bulkhead, with 0.25° eccentric suspension mount holes. The eccentric holder stands allow more precise toe-in setting with 0.25° increments. Suspension holders are CNC-machined from premium Swiss 7075 T6 aluminum, and provide the lightest & strongest possible support framework for the car.

• 3x heavier than alu holders • Eliminates need for additional chassis weights • Eliminates negative chassis flex • Equal weight addition left & right • Available for front or rear suspension Brass suspension holders were created to add additional weight to the car to attain the minimum weight limit, and to replace other chassis-mounted weights which negatively influence...

Authentic XRAY alu rear lower suspension holder for the REAR of the rear bulkhead of T4. The lower design of the suspension holders helps to generate more traction. Recommended for asphalt tracks with low-to-medium traction. Must be used with: right alu holder #303716-O and Left alu holder #303717-O. Suspension holders are CNC-machined from premium Swiss 7075 T6 aluminum and...

Anti Roll Bar for Ball Bearings - Rear 1.1mm

Anti Roll Bar for Ball Bearings - Rear 1.2mm

Anti Roll Bar for Ball Bearings - Rear 1.4mm

Anti Roll Bar for Ball Bearings - Rear 1.5mm

Anti Roll Bar for Ball Bearings - Rear 1.6mm

XB4 2016 - Graphite Gear Diff Gears - LOW (2+4) Replacement for 304931

GEAR DIFF OUTDRIVE ADAPTER - HUDY SPRING STEEL™ (2)

MULTI-DIFF LOCKING AXLE - HUDY SPRING STEEL

Original XRAY spare and option parts! There are several types of spool outdrives: 305134 - Springsteel - 8.28g - durable, heavy, allround solution 305135 - Composite - 4.00g - light, without blades, for stock semi-pro drivers 305136 - Alu - 3.56g - very light, with blades, for stock pro-drivers 305137 - Springsteel LIGHTWEIGHT - 6.71g - durable, best solution between...

ALU SOLID AXLE DRIVESHAFT ADAPTERS - HARD COATED (2) There are several types of spool outdrives: 305134 - Springsteel - 8.28g - durable, heavy, allround solution 305135 - Composite - 4.00g - light, without blades, for stock semi-pro drivers 305136 - Alu - 3.56g - very light, with blades, for stock pro-drivers 305137 - Springsteel LIGHTWEIGHT - 6.71g - durable, best solution...

STEEL SOLID AXLE DRIVESHAFT ADAPTERS - HUDY SPRING STEEL™ (2) There are several types of spool outdrives: 305134 - Springsteel - 8.28g - durable, heavy, allround solution 305135 - Composite - 4.00g - light, without blades, for stock semi-pro drivers 305136 - Alu - 3.56g - very light, with blades, for stock pro-drivers 305137 - Springsteel LIGHTWEIGHT - 6.71g - durable, best...

TIMING BELT PULLEY 38T FOR MULTI-DIFF

Genuine XRAY parts. Original is always best! Will fit as spare / optional to 305332 / 305333 / 305334

ECS (ES) Drive Shaft - 50mm - for 2mm Pin HUDY Spring Steel Fits to 305333 - ECS ES (Extra Strong) Drive Shaft - 50mm - HUDY SPIRNG STEEL (1 piece) or to convert 305332 - ECS ES (Extra Strong) Drive Shaft - 52mm - HUDY Spring Steel(1 Stück).

T4 POM Blades - extra strong - 3.5mm - ORANGE (4 pcs)

ECS Drive Shaft Coupling for 2mm Pin - HUDY Spring Steel

ECS Drive Shaft Case for 2mm Pin HUDY Spring Steel

DRIVE SHAFT 50MM - HUDY SPRING STEEL