Composite right 0° graphite (ECS)

Composite C-Hub left 0° graphite (ECS)

Composite C-Hub right 4° graphite (ECS)

ALU DUAL SERVO SAVER ARM + BALL-BEARINGS (2) More precision, more steering angle.

ALU STEERING POST FOR DUAL SERVO SAVER (2 pieces)

Genuine XRAY parts for your T4!

The 8mm steering plate was developed to improve the cornering speed. This steering plate has less steering response and is recommended for large asphalt tracks with long sweepers to improve cornering speed or very technical carpet tracks to eliminate oversteering in the chicanes. The bearings are factory pressed into the steering plate which eliminates play in the assembly....

ADJ. TURNBUCKLE L/R 40 MM - HUDY SPRING STEEL (2)

ALU ADJ. TURNBUCKLE M3 L/R 39 MM - ORANGE - SWISS 7075 T6 (2 pieces)

ALU FRONT LOWER 1-PIECE SUSPENSION HOLDER - FRONT - FF

• 3x heavier than alu holders • Eliminates need for additional chassis weights • Eliminates negative chassis flex • Equal weight addition left & right • Available for front or rear suspension Brass suspension holders were created to add additional weight to the car to attain the minimum weight limit, and to replace other chassis-mounted weights which negatively influence...

Will lower the suspension mount by 0.5mm - as replacement for the standard mount 302710. Searching for the other side? 302712-O :-) Will fit to any T4 starting with the 2014!

ALU FRONT LOWER 1-PIECE SUSPENSION HOLDER - REAR - FR

• 3x heavier than alu holders • Eliminates need for additional chassis weights • Eliminates negative chassis flex • Equal weight addition left & right • Available for front or rear suspension Brass suspension holders were created to add additional weight to the car to attain the minimum weight limit, and to replace other chassis-mounted weights which negatively influence...

Will lower the suspension mount by 0.5mm - as replacement for the standard mount 302720. Searching for the other side? 302722-O :-) Will fit to any T4 starting with 2014!

Genuine XRAY spares!

Genuine XRAY spares!

Genuine XRAY spares!

The new feature of the T4'20 arms is to mount the shocks lower. To use this option you need to use optional low ULP shock towers which allows you to mount shocks 4mm lower to lower the CG. With the lower shock mounting, the car is more stable as it rolls less, is easier to drive over chicanes, and has improved steering response. Recommended for medium-high technical tracks,...

The SLP (Super-Low Profile) shock towers allow to mount the shocks lower to lower the CG. With the lower shock mounting, the car is more stable as it rolls less, is easier to drive over chicanes, and has improved steering response. Recommended for medium-high technical tracks, especially for carpet. Made from 3.0mm thick premium-grade graphite material to guarantee maximum...

Genuine spare and option parts from XRAY!

SET OF ALU SHIM (0.5MM, 1.5MM, 2.5MM)

SET OF ALU SHIM (1.0MM, 2.0MM, 3.0MM)

T4 2014 - Alu Shims (3x6x0.5mm) - black

T4 2014 - Alu Shims (3x6x0.5mm) Will be delivered BULK.

ALU SHIM 3x6x1.0MM (10)

ALU SHIM 3x6x1.0MM - ORANGE (10)

XRAY T2 Alu Scheiben - 3x6x2.0mm (10 Stück)

ALU SHIM 3x6x2.0MM - ORANGE (10)

Alu Shim 3 x 6 x 3.0mm (10 pieces)

Alu Shim

ALU SHIM 3x6x6.0MM (10)

ALU SHIM 3x6x6.0MM - BLACK (10)

REAR SUSPENSION ARM - HARD - 1-HOLE - V2

REAR SUSPENSION ARM - EXTRA-HARD - 1-HOLE - V2

REAR SUSPENSION ARM - EXTRA-HARD - 2-HOLE

REAR SUSPENSION ARM - GRAPHITE - 1-HOLE

T4 2014 Rear Suspension Arm - hard

T4 2014 Rear Suspension Arm - Graphite

ARS - Active Rear Suspension Arm - Hard- 1-Hole

ARS Active Rear Suspension Arm - Graphite - 1-Hole

The aluminum suspension arm is a direct replacement for the standard composite graphite arm. The aluminum arm works well on high traction or permanent carpet tracks as it makes the car easier to drive with less stopping and better cornering speed. The arms are available for front and rear and are available either individually or as a set. Features a single optimized shock...

Completely redesigned front long suspension arm is 7mm longer than the short arms, which helps to generate more grip in low traction conditions and improves stability on higher traction surfaces. The front RIGHT suspension arm features a standard shock mounting position as well as a new 4mm lower position to lower the CG (must be used with optional lower ULP shock tower)....

Completely redesigned front long suspension arm is 7mm longer than the short arms, which helps to generate more grip in low traction conditions and improves stability on higher traction surfaces. The front RIGHT suspension arm features a standard shock mounting position as well as a new 4mm lower position to lower the CG (must be used with optional lower ULP shock tower)....

T4 2014 Graphite Rear Arm Stiffener (2) Important note : The carbon plates are fastened with screws M2.5 with 1.5mm allen head. Therefore it is extremely important to use a hex screwdriver is in a state of 100 %. A hexagon with wear will destroy the screws . It is also necessary to go with caution to the screws . Not tighten too fast , do not fix sloping ! In order to be...

Graphite ARS Rear Lower Arm Plate 1.6mm (L+R)

ALU ADJ. TURNBUCKLE L/R 26 MM - ORANGE - SWISS 7075 T6 (2 pieces)

COMPOSITE UPRIGHT 1° OUTBOARD TOE-IN - RIGHT - MEDIUM

COMPOSITE UPRIGHT 0° OUTBOARD TOE-IN - MEDIUM

COMPOSITE UPRIGHT 1° OUTBOARD TOE-IN - RIGHT - HARD

GRAPHITE UPRIGHT 0° OUTBOARD TOE-IN

COMPOSITE UPRIGHT 1° OUTBOARD TOE-IN - LEFT - MEDIUM

COMPOSITE UPRIGHT 0° OUTBOARD TOE-IN - 1-HOLE - MEDIUM

COMPOSITE UPRIGHT 1° OUTBOARD TOE-IN - LEFT - HARD

COMPOSITE UPRIGHT 0° OUTBOARD TOE-IN - 1-HOLE - HARD

Genuine XRAY spares!

ALU REAR LOWER 1-PIECE SUSPENSION HOLDER - REAR - RR

• 3x heavier than alu holders • Eliminates need for additional chassis weights • Eliminates negative chassis flex • Equal weight addition left & right • Available for front or rear suspension Brass suspension holders were created to add additional weight to the car to attain the minimum weight limit, and to replace other chassis-mounted weights which negatively influence...

Eccentric holder - for 0.25mm wider front in the rear suspension.

Will increase the stiffness of the rear area and reduce flex. Additionaly it will increase the weight (+15g)